afarkasg wrote:
Here is the description i found in german:
1. Kopiere das Originalbild 2 mal und wandle die Kopien in SW um und invertiere sie.
2. Nun gibst Du der ersten Kopie eine Ebenenmaske, kopierst die zweite Kopie und fügst sie in die Ebenenmaske der ersten Kopie ein.
3. Die Ebenenmaske leicht weichzeichnen (Gauss, je nach Bildgröße ca. 10-30 px)
4. Die zweite Kopie kann gelöscht werden; die erste Kopie mit der Maske nun auf Modus "Ineinanderkopieren" (probiere auch mal "Weiches Licht") setzen, Deckkraft anpassen, im script sind es 60%
5. Die Ebenen vereinen und zwei neue Kopien machen
6. Die untere Kopie kräftig mit USM schärfen (z.B. 2px, 200%)
7. Auf die obere Kopie einen Kantenfilter anwenden (im skript ist es Sobel, je nach Bild kann auch ein anderer gut sein). Das Kantenbild in SW umwandeln und den Kontrast erhöhen, das Bild muss weiße Kanten auf schwarzem Grund zeigen.
8. Nun dem geschärften Bild wieder eine Ebenenmaske geben, dann das Kantenbild kopieren und in die Ebenenmaske einfügen (wie oben auch); das Kantenbild kann jetzt gelöscht werden.
9. Die geschärfte Ebene mit der Kantenmaske auf Modus "Leuchtkraft" setzen, Deckkraft ca. bei 80%
10. Die Ebenen wieder vereinen
11. Den lokalen Kontrast erhöhen durch USM mit großem Radius und geringem Wert (ca. 60 px und 30-40%)
12. Jetzt nochmal zwei Kopien machen und beide in SW umwandeln
13. Die untere auf Modus "Bildschirm" setzen bei ca. 60% Deckkraft
14. Die obere auf Modus "Ineinanderkopieren" oder "Weiches Licht" bei 100%
15. Im Prinzip fertig, zur Verbesserung (empfohlen, im script als wählbare Option), der Bildschirm-Ebene noch eine Ebenenmaske geben, dort eine Kopie dieser Ebene einfügen, die Maske invertieren und weichzeichnen (wie in den ersten Schritten)
16. Zur Verstärkung des Effektes evtl. die Ineinanderkopieren-Ebene nochmal duplizieren und im gleichen Modus die Deckkraft verringern (ca.25%).
I dont understand german, the google translation is a mess in any language i know
1. Copy the original image 2 times and convert the copies to SW and invert them.
2. Now you give the first copy a layer mask, copy the second copy and paste it into the layer mask of the first copy.
3. Slightly flatten the plane mask (Gauss, depending on the picture size approx. 10-30 px)
4. The second copy can be deleted; the first copy with the mask now on mode "copy" (try also times "soft light") set, opacity adjust, in the script it is 60%
5. Merge the layers and make two new copies
6. Sharpen the lower copy vigorously with USM (e.g., 2px, 200%).
7. Apply an edge filter to the upper copy (in the script it is Sobel, depending on the image, another can be good). Convert the edge image to SW and increase the contrast, the image must show white edges on a black background.
8. Now give the sharpened image a layer mask, then copy the edge image and paste it into the layer (as above); the edge image can now be deleted.
9. Set the sharpened plane with the edge mask to "luminosity" mode, cover force approx. 80%
10. Reunite the levels
11. Increase the local contrast by USM with large radius and low value (about 60 px and 30-40%)
12. Now again make two copies and convert both to SW
13. Set the lower to "Screen" mode with approx. 60% opacity
14. The upper mode of "Inverse" or "Soft Light" mode at 100%
15. In principle, to make a copy of this layer, invert and make the mask inverted (as in the first steps), for the improvement (recommended, in the script as a selectable option), add a layer mask to the screen level,
16. To enhance the effect, duplicate the interleave layer again and reduce the opacity in the same mode (approx.25%).
USM = Unsharp Mask i believe.
SW = not quite sure maybe black and white?
step number 10 probably means merge the layers