Gimp Filter BA_SpiderPaint

hardy111 · **Joined:** Jun 16, 2016 **Posts:** 137

Hi there,
there is the filter
"1BA_SpiderPaint_v2c_qt2.py" also for the Gimp version 2.10 and G'Mic QT?

I am very happy about a message!

Best regards, Hardy

Issabella · **Posted:** Thu Mar 19, 2020 2:44 am **(#2)**

Hardy 111, I have this one. It's an old version. Perhaps you can actualize it to use currently. :bigthup

hardy111 · **Joined:** Jun 16, 2016 **Posts:** 137

Hello Issabella,
thank you for your link. I use Gimp version
2.10.12 german and G'Mic QT. Unfortunately
the filter does not work under this constellation.

Greetings from Germany Hardy

Issabella · **Posted:** Thu Mar 19, 2020 3:51 am **(#4)**

Sorry Hardy, that it doesn't work for you. Hopefully, somebody of our great coders was able to repair it. Luck!

nelo · **Posted:** Thu Mar 19, 2020 4:22 am **(#5)**

Hasn't it been fixed already?
viewtopic.php?f=9&t=15440

Nidhogg · **Posted:** Thu Mar 19, 2020 4:50 am **(#6)**

No that is same version. You can see the post is edited 2017, it was made for 2.8.16.
I tried yesterday, got all the layer modes fixed but it still gave some error and I had to go sleep.
I'm sure it will be fixed in no time.

MareroQ · **Posted:** Fri Mar 20, 2020 8:14 am **(#7)**

You can try this version.
I only tested for Gimp 2.10.18, G'mic 2.8.4.
Just beware - as Nidhogg wrote, it is possible that some combinations of parameters give errors (this is a slow plugin and I haven't tested many combinations).
I've made 70 corrections - maybe more will be needed. :cool

Older version removed.
You can download from here:
viewtopic.php?f=9&t=18138#p248848

Nidhogg · **Posted:** Fri Mar 20, 2020 8:24 am **(#8)**

I'm running into same exact error than earlier.

....BA_SpiderPaint_v2.10_qt2.py", line 789, in BA_SpiderPaint_v2_10_qt2
lay5.mode = LAYER_MODE_SCREEN_LEGACY
error: could not set mode on layer (ID 173)

This is 2.10.12, MX Linux. I will try on another machine.

hardy111 · **Joined:** Jun 16, 2016 **Posts:** 137

Hello MareroQ,
Thank you for adapting to Gimp 2.10 and G'Mic QT.
For me the plug-in runs under Gimp 2.10.12 german
and works without problems. In this way I would like
to thank you again for the adjustment.

Greetings from Germany Hardy

hardy111 · **Joined:** Jun 16, 2016 **Posts:** 137

Hi there,
here is one of my first results.

Attachment:

test.png [ 2.25 MiB | Viewed 4817 times ]

Regards Hardy

mackenzieh · **Posted:** Fri Mar 20, 2020 11:19 pm **(#11)**

Do Brian's other plugins work? I ask because I've tried them in the past and they have failed.

MareroQ · **Posted:** Sat Mar 21, 2020 6:53 am **(#12)**

Hi Mackenzieh.
What plugins are You talking about?
Because these work:

mackenzieh · **Posted:** Sat Mar 21, 2020 1:05 pm **(#13)**

MareroQ wrote:

Hi Mackenzieh.
What plugins are You talking about?
Because these work:

I'm talking about the ones in your screen shot. Do they work for GIMP 2.10 windows 64 Bit? If they do, where can I find them?

MareroQ · **Posted:** Sat Mar 21, 2020 1:39 pm **(#14)**

They work. I will send them all tomorrow.

mackenzieh · **Posted:** Sat Mar 21, 2020 1:56 pm **(#15)**

MareroQ wrote:

They work. I will send them all tomorrow.

Thanks, MareroQ!

Issabella · **Posted:** Tue Nov 24, 2020 9:47 am **(#16)**

MareroQ.
BA_Spider Paint stops at that point (see the shot)
I'm sure the image has an alpha channel. What can it be?
Thank you so much for your attention.

MareroQ · **Posted:** Wed Nov 25, 2020 8:30 am **(#17)**

Hi Issabella.

Thanks for reporting.
I forgot to remove the old version from post # 7 (fixed)
You can download the corrected version from here (two possibilities):
viewtopic.php?f=9&t=18138#p248848

Off topic:
Why are you using the old version of gimpfu.py (despite some errors like eg.: viewtopic.php?f=9&t=18927#p258561)?
Have you tried to install a newer version:
https://www.gimpscripts.net/2020/10/pyt ... hrink.html
Was there a problem?

Issabella · **Posted:** Wed Nov 25, 2020 10:49 am **(#18)**

Thank you so much MareroQ, but the problem continues.

I don't get to make Spider Paint work. any of the two versions.
About gimpfu. Yes, I tried the newer version and I had many problems. it affected to BRL logos.

MareroQ · **Posted:** Wed Nov 25, 2020 11:44 am **(#19)**

The command name has changed in G'mic.
Can You try again?
BRL = Bevel-Reflect-Logo.scm?
More details (because these are two separate things - gimpfu.py only affects python plugins and only script-fu.exe for scripts).

Issabella · **Posted:** Wed Nov 25, 2020 12:00 pm **(#20)**

I have those items you say.
What must I change?

	Similar Topics	Replies
	HELP! I Cant get Spiderpaint to work	5
	cli345's cartoon filter as a native GEGL Filter.	10
	My last Aquarelle filter	21
	Carve.. filter	3
	Made with new filter in G'mic	23